Posts

Showing posts from October, 2019

ZVS Tesla Coil Power Supply Boost High Voltage Generator Driver Board Induction Heating Module DIY Production Kit

Image
Get ZVS Tesla Coil Power Supply Boost High Voltage Generator Driver Board Induction Heating Module DIY Production Kit Product parameters: Product size: 74mm * 77.8mm; Shell size: 102*88*42.5MM; Input voltage: DC 12V-30V Power requirements: less than 12V ≥ 5A 15V or more ≥ 15A Operating frequency: 30kHz-50kHz adaptive Secondary parameter: 5T+5T About the length of the discharge arc: When the input voltage is 12v/5A, the arc distance of the high voltage discharge is about 1-2 cm. The larger the input voltage and current, the greater the output power and the longer the arc discharge distance. The maximum input is 30v/10A, and the maximum length is more than 5 cm. If the arc is too short, check if the input power is sufficient. Power supply selection: If the battery is used, use a model battery with a discharge rate of 25C or higher. Do not use an ordinary electric vehicle battery or a small battery. If you use a switching power supply, you should choose a 12V or more switching power suppl

Rectangular Wave Signal Generator DIY Kit Electronic Skills Training Parts

Image
Get Rectangular Wave Signal Generator DIY Kit Electronic Skills Training Parts Description: Dimensions: 51*27mm Board material: single side 1.6mm FR-4 sheet Supply voltage: 5V Name Parameter PCB mark Quantity Resistor 1K R1 1 4.7K R2 1 22K R3 1 220ohm R4 1 4.7K R5 1 Diode 1N4001 D1-D4 4 Adjustable potentiometer 100K RP1 1 Integrated voltage regulator 78L05 U1 1 IC NE555 U2 1 Electrolytic capacitor 470uF/16V C1 1 1uF/50V C2 1 Ceramic capacitor 104 C3 1 103 C4 1 Transistor 9013 Q1 1 LED 3mm green D5 1 3mm red D6 1 Jumper cap   S1, S2 2 Single row Pin 2p Tp1, GND, S 8 PCB     1 Package included: 1 x Rectangular Wave Signal Generator DIY Kit Rectangular Wave Signal Generator DIY Kit Electronic Skills Training Parts See detail

555 Trigger Circuit Student Soldering Practice Board Electronic Production DIY Kit

Image
Get 555 Trigger Circuit Student Soldering Practice Board Electronic Production DIY Kit Description: Dimensions: 57*40mm Supply voltage: 5V Name Parameter PCB mark Quantity Resistor 1K R1 R3 R5 R6 R9 5 100K R2 R4 2 10K R7 R8 2 Diode 1N4007 VD1-VD4 4 Electrolytic capacitor 220uF C1 1 100uF C2 1 47uF C3 1 LED 3mm red LED1-LED3 3 Tact switch 6*6 S1 1 Adjustable resistor 200K W1, W2 1 IC LM7812 IC1 1 NE555 IC2, IC3 2 Ceramic capacitor 103 C4-C8 4 PCB     1 Package included: 1 x 555 Trigger Circuit DIY kit 555 Trigger Circuit Student Soldering Practice Board Electronic Production DIY Kit See detail

3pcs AI-Thinker USB to Serial Port CP2102 2.4G 433M USB to TTL Communication Module USB-T1 Adapter Board

Image
Get 3pcs AI-Thinker USB to Serial Port CP2102 2.4G 433M USB to TTL Communication Module USB-T1 Adapter Board Driver: Click here to open  ( Windows/Mac_OS/Linux ) Features: Fully compatible with Windows, Mac OS, Linux, support for both X86 and X64 Size: 52.5mm x 17.6mm   Functions:   Automatic recovery fuse: intelligent anti-burn, equipped with 500mA automatic recovery insurance, automatic disconnection of current over 500mA, protect your device and USB port, even if it is short circuit will not affect, after the circuit is normal, you can restore the link. CP2102 chip: USB interface chip CP2102, high stability and high performance, communication speed up to 2Mbps. The TTL level is compatible with the 3V3 level standard. It comes with 5V and 3.3V, 4.2V power output ports, which can supply power to the MCU system. The DTR/RTS output interface can be reserved, and the level of the two pins can be overridden through the serial port. When some MCUs download the program, the reset can be

3pcs Thermal Sensor Module Temperature Switch Thermistor Sensor Board For Arduino

Image
Get 3pcs Thermal Sensor Module Temperature Switch Thermistor Sensor Board For Arduino Uses:   Temperature detection, temperature control sensors , ambient temperature detection   Features:   1. Using the NTC thermistor sensor, good sensitivity 2. The comparator output signal is clean, good waveform, driving ability, more than 15mA. 3. Adjust the temperature distribution position detection threshold 4. The working voltage 3.3V-5V 5. The output format: digital switching outputs ( 0 and 1 ) 6. Fixed bolt holes for easy installation 7. Small PCB board size: 3.2cm x 1.4cm 8. Using a wide voltage LM393 comparator   Module for use:   1. The thermal resistance of the module is very sensitive to the ambient temperature, typically for detecting the temperature of the surrounding environment ; 2. Through the potentiometer adjustment, you can change the temperature detection threshold ( ie, control temperature ), such as the need to control the ambient temperature is 50 degrees, the module in